|
|
نام محصول: شیلد نمایشگر TFT رنگی 3.5 اینچ 320X480 برای آردوینو UNO بدون تاچ |
مدل: ARD-00070 |
ناموجود |
|
|
|
توضیحات محصول |
Product Picture Product Description- Supports development boards such as Arduino UNO and Mega2560 for plug-in use without wiring
- 480X320 resolution, clear display, support for touch function
- Support 16-bit RGB 65K color display, display rich colors
- 8-bit parallel bus, faster than serial SPI refresh
- On-board 5V/3.3V level shifting IC, compatible with 5V/3.3V operating voltage
- Easy to expand the experiment with SD card slot
- Provides an Arduino library with a rich sample program
- Military-grade process standards, long-term stable work
- Provide underlying driver technical support
Product ParametersName | Parameter | Display Color | RGB 65K color | SKU | MAR3501(have touch screen)/MAR3502(have no touch screen) | Screen Size | 3.5(inch) | Type | TFT | Driver IC | ILI9486 | Resolution | 480*320 (Pixel) | Module Interface | 8-bit parallel interface | Active Area | 73.44*48.96(mm) | Module PCB Size | 85.49*55.63(mm) | Operating Temperature | -20℃~70℃ | Storage Temperature | -40℃~70℃ | Operating Voltage | 5V/3.3V | Power Consumption | TBD | Product Weight(Package containing) | 44g(have touch screen),55g(have no touch screen) |
Interface DefinitionNumber | Pin Label | Pin Description | 1 | LCD_RST | LCD bus reset signal, low level reset | 2 | LCD_CS | LCD bus chip select signal, low level enable | 3 | LCD_RS | LCD bus command / data selection signal, low level: command, high level: data | 4 | LCD_WR | LCD bus write signal | 5 | LCD_RD | LCD bus read signal | 6 | GND | Power ground | 7 | 5V | 5V power input | 8 | 3V3 | 3.3V power input, this pin can be disconnected | 9 | LCD_D0 | LCD 8-bit data Bit0 | 10 | LCD_D1 | LCD 8-bit data Bit1 | 11 | LCD_D2 | LCD 8-bit data Bit2 | 12 | LCD_D3 | LCD 8-bit data Bit3 | 13 | LCD_D4 | LCD 8-bit data Bit4 | 14 | LCD_D5 | LCD 8-bit data Bit5 | 15 | LCD_D6 | LCD 8-bit data Bit6 | 16 | LCD_D7 | LCD 8-bit data Bit7 | 17 | SD_SS | SD card SPI bus chip select signal, low level enable | 18 | SD_DI | SD card SPI bus MOSI signal | 19 | SD_DO | SD card SPI bus MISO signal | 20 | SD_SCK | SD card SPI bus clock signal |
Product DocumentationConnect to Arduino | |
---|
Arduino UNO direct insertion picture | Arduino Mega2560 direct insertion picture |
How to use on Arduino- Step 1: Download the test program
- Download the Arduino test program from the Program Download column
- For a description of the relevant test procedures, please refer to the test program documentation in the package
- Step 2: Connect the Arduino development board
- Plug the module directly into the Arduino development board ( Do not plug in?)
- After the module is plugged in, power on the Arduino board
- Step 3: Copy the dependent library
- Make sure the Arduino IDE is installed on your computer (if it is not installed: Arduino IDE download URL)
- After installing the Arduino IDE, you need to copy the dependent library to the Arduino project directory as follows:
- (1) Decompress the downloaded test package
- (2) Copy the dependent libraries in the Install libraries directory in the package (shown below) to the libraries folder
- of the Arduino project directory ( Don't know the Arduino project directory?)
- Step 4: Compile and download the program to the development board
- Open the sample in the Example directory of the package to test, compile and download( Don't know how to compile and download?)
- Step 5: Observe the running of the program
- After the program is downloaded, run it directly and observe the running status. If it can be displayed normally, the program runs
- successfully, as shown in the following figure (take the colligate_test test program as an example):
Program DownloadReference MaterialsCommon Software |
|
|
|