انتخاب واحد پولی:
فارسی انگلیسی
سبد خرید: (0) مورد
خوش آمدید, کاربر گرامی
پشتیبانی آنلاین
Live Support
شاخه ها
اطلاعيه ها
اطلاعيه هامرا از تغييرات محصول مبدل RS-232 به RS-485 دو طرفه فول داپلکس TCC-80 با ایزولاسیون 2.5کیلو ولت محصول MOXA آگاه كن.
سبد خريد
 
0 مورد
مقایسه محصولات
محصولی برای مقایسه انتخاب نشده است!
ورود به سيستم
آدرس پست الكترونيك:
كلمه عبور:

کلمه عبورتان را فراموش کرده اید؟
هنوز ثبت نام نکرده اید؟
تگ محصولات
مقالات
مقالات جدید
تمامی مقالات
تمامی موضوعات
 مقالات متفرقه
RSS مقالات

مبدل RS-232 به RS-485 دو طرفه فول داپلکس TCC-80 با ایزولاسیون 2.5کیلو ولت محصول MOXA[CONV-00061]کد کالا : CONV-00061

مبدل RS-232 به RS-485 دو طرفه فول داپلکس TCC-80 با ایزولاسیون 2.5کیلو ولت محصول MOXA
قیمت: 599,800تومان
 
 
Features and Benefits
  • External power source supported but not required
  • Compact size
  • Converts RS-422, and both 2-wire and 4-wire RS-485
  • RS-485 automatic data direction control
  • Automatic baudrate detection
  • Built-in 120-ohm termination resistors
  • 2.5 kV isolation (for TCC-80I only)
  • LED port power indicator

 

Introduction

The TCC-80/80I media converters provide complete signal conversion between RS-232 and RS-422/485, without requiring an external power source. The converters support both half duplex 2-wire RS-485 and full duplex 4-wire RS-422/485, either of which can be converted between RS-232’s TxD and RxD lines. In addition,the TCC-80/80I’s 15 kV ESD protection guards against damage from electrostatic discharge, and the TCC-80I is the world’s first high-speed, port-powered converter with 2.5 kV isolation.

Automatic data direction control is provided for RS-485. In this case, the RS-485 driver is enabled automatically when the circuitry senses the TxD output from the RS-232 signal. This means that no programming effort is required to control the transmission direction of the RS-485 signal. Moreover, the TCC-80I’s patented LED port power indicator lets you check whether or not the TCC-80I is receiving enough power.

 

Port Power over RS-232

The RS-232 port of the TCC-80/80I is a DB9 female socket that can connect directly to the host PC, with power drawn from the TxD line. Regardless of whether the signal is high or low, the TCC-80/80I can obtain enough power from the data line. However, external power can be used if the handshake line is not available, if the serial cable is too long, or if the RS-232 device is a low power device. For external power, a 5 to 12 VDC power supply can be connected using an adaptor or a USB power cord.

 

 

Port Power Dissipation

When installing a TCC-80 or TCC-80I converter, it is important to pay attention to power consumption, RS-232 cable length, and RS-422/485 transmission distance. In general, the TCC-80 and TCC-80I obtain 50 mW of power from the power source. Standard PC COM ports can provide 70 to 90 mW of power if the TxD, RTS, and DTR lines are connected. Moreover, the RS-232 cable should be shorter than 15 m (@ 9600 bps) to ensure that less power is lost from the host/device to the TCC-80. The remainder of the supplied power is used for transmitting the RS-422/485 signal.

 

Port Power and Optical Isolation

The RS-232 port of the TCC-80/80I is a DB9 female socket that can connect directly to the host PC, with power drawn from the TxD line. Electrical 2.5 kV isolation for the TCC-80I is achieved with a photo coupler that transforms the electrical signal into light, and then re-transforms the light back into an electrical signal on the other side. In this way, the two electrical circuits are completely isolated from each other. This also protects the devices from ground loop currents, reduces damage caused by data loss, and prevents damage to the communication interfaces.

 

LED Port Power Indicator

It’s easy enough to test the serial device with a multimeter to determine that the serial device will provide enough power to the media converter. However, it’s even easier to let the TCC-80I test the device for you. Simply connect the TCC-80I to the device’s RS-232 port and set the SW4 switch to Test mode. If the patented port power LED indicator lights up, the TCC-80I is receiving enough power. If the LED does not light up, you will need to attach an external power source to the TCC-80I.

افزودن به لیست مقایسه نظرات بازگشت
کپی‌رایت © 2019 ایران ماژول الکترونیک
راه اندازی شده توسط فروشگاه ساز ویرچو