ماژول کنترل دما ی تک رله WX-101W

ماژول کنترل دما ی تک رله WX-101W

مشخصات

نحوه استفاده

با استفاده از کلیدهای جهت دار دمای تحریک را تعیین میکنیم.

F-1 با زدن دکمه SET وارد قسمت تنظیمات شده و با دوباره فشار دادن وارد قسمت تنظیمات F-1 می شوید. با کلیدهای جهت دار از بین دو مد Cooling و Heating انتخاب کنید.

Cooling: در صورت بالا رفتن دما از حداکثر مجاز تعیین شده رله وصل می شود(هدف، کنترل سیستم سرمایشی)

Heating: در صورت پایین آمدن دما از حداقل تعیین شده رله وصل می شود(هدف، کنترل سیستم گرمایشی)

F-2 با زدن دکمه SET و با استفاده از کلیدهای جهت دار بین پارامترها امکان جابجایی وجود دارد. با انتخاب F-2 وارد تنظیمات هیسترزیس شوید. این پارامتر تعیین کننده مقدار تلورانس حساسیت می باشد. به طور مثال دمای تعیین شده 30 درجه است بعد از گذشتن از این دما سیستم رله را قطع می کند در صورتی که حساسیت سیستم روی 2 درجه تنظیم شده باشد تا 28 درجه رله تغییر وضعیت نمی دهد.

F-3 با طی مراحل فوق وارد قسمت F-3 که به منظور کالیبراسیون می باشد. به این صورت که با توجه به اختلاف دمای اندازه گیری شده با دمای واقعی یک Offset برای سیستم تعریف می شود. که در صورت نداشتن دماسنج دقیق مقدار پیش فرض صفر مطلوب می باشد.

F-4 تعیین زمان تاخیر برای تغییر وضعیت رله بعد از گذشتن از حد مجاز دما (قابل تنظیم از 0 تا 10 دقیقه با دقت 1 دقیقه)

در صورتی که سنسور متصل نشده باشد و یا داده ای ارسال نکند پیام “EO” بر روی صفحه نمایش ظاهر می شود.


Specification

Temperature range :-50-110 C
Dimensions: 48.5 * 40mm
Temperature control mode: ON / OFF
Resolution  When temperature is 0.1 C, the resolution is -9.9~99.9, other temperature segment is 1 C
Control accuracy: 0.1 C
Hysteresis accuracy: 0.1 C
Refresh rate: 0.5S
High temperature protection   0-110 C
Supply voltage: DC 12V
Static current: ≤ 35MA, attract current ≤ 65MA
Output voltage: DC 12V
Output power: 12A relay
Measurement input: NTC (10K 0.5%) Waterproof Sensor
Environmental requirements: -10 ~ 60 C   Humidity 20% -85%

Instruction

First use a connection power supply and load line, can for power supply of temperature control board and display is the current temperature.Press”+“or” —”to adjust the control temperature, After press ‘setting' key to save. Out. The temperature control board for automatic control mode of heating. According to the set temperature automatic control relay on-off, temperature control board relay electric contactor is 12A, can match most of the high power load equipment.

Digital display and status indication

Light up: relay connected Light off: relay disconnect For sensor: display “EO" for sensor open circuit, display ‘---' for sensor short circuit, no matter what kind of fault control board will cut off the load and automatically protect!

Function CodeFunctional SpecificationSet RangeFactory Settings
F-1Heating/ coolingHH/CCHH
F-2Back to setting0.1~20℃2℃
F-3Temperature calibration-5.0℃~5.0℃0.0℃
F-54Delay start time0-10minutes0
Automatically ProtectHigh temperature protectionMore than120℃Automatic
Disturbance DisplayEOProbe open circuitAutomatic
Disturbance Display---Probe short circuitAutomatic

Electricity factory Setting:
 hold the setkey, set the release button 3 seconds torestore the factory Settings!

Control mode:
 press "set" button at once, Let it display F - 1, and then press "set"button to enter the F - 1 manu ,and then click

"+" button display “H H ” for heating control mode, according to "-" button display "CC" to refrigeration control mode, Last press

"set" for preserve and exsit.

Temperature Setting:
 under the displays the current temperature directly at '+' or '-'button can set the required control point

temperature, After finish the installation.press "set" for preserve and exsit.

Return difference Setting:
 Press "set"button display "F - 1", then press the "+"button or "-" button can adjust function, when

display F - 1 ,press "+" button to let its display F - 2, This time press "set" button to enter at F - 2 functions, it's return difference

parameter adjustment interface,press the "+" or "-" button to adjust return difference values, the return difference mean start

and stop temperature difference, if want to control the heating ,If control temperature setting 30 degrees, Return difference set to

2, is the current temperature over 30 degrees, Relay disconnect.lower than 28 degrees relay connect, The Return difference of 2!

Refrigeration control is opposite control state!

Temperature correction Setting:
 adjustment function is display F -3, according to press a"set" button to enter the F - 3 parameters to adjust interface, the adjusting range of -5.0~ 5.0, when the temperature is not accurate, can be temperature

correction according this function, if the measurement of the current temperature is higher than the actual temperature of 0.5 degrees, calibration parameters can be adjusted to -0.5, press "setting" for preserve.6. 

Delay start time Setting:
after "stop "start to the next start, To satisfy setting time and then can be start , generally for protect

the compressor at refrigeration control mode, the heating control can be set to "0", the factory default is "0", delay time "0 "to "10 "minutes.