انتخاب واحد پولی:
فارسی انگلیسی
سبد خرید: (0) مورد
خوش آمدید, کاربر گرامی
پشتیبانی آنلاین
Live Support
شاخه ها
اطلاعيه ها
اطلاعيه هامرا از تغييرات محصول بورد درایور موتور Romeo-All in One آگاه كن.
سبد خريد
 
0 مورد
مقایسه محصولات
محصولی برای مقایسه انتخاب نشده است!
ورود به سيستم
آدرس پست الكترونيك:
كلمه عبور:

کلمه عبورتان را فراموش کرده اید؟
هنوز ثبت نام نکرده اید؟
تگ محصولات
تسلست
مقالات
مقالات جدید
تمامی مقالات
تمامی موضوعات
 مقالات متفرقه
RSS مقالات

بورد درایور موتور Romeo-All in One[ROB-00011]کد کالا : ROB-00011

بورد درایور موتور Romeo-All in One
قیمت: ناموجود
 
 

Specification

  • Atmega 168/328
  • 14 Channels Digital I/O
  • 6 PWM Channels (Pin11,Pin10,Pin9,Pin6,Pin5,Pin3)
  • 8 Channels 10-bit Analog I/O
  • USB interface
  • Auto sensing/switching power input
  • ICSP header for direct program download
  • Serial Interface TTL Level
  • Support AREF
  • Support Male and Female Pin Header
  • Integrated sockets for APC220 RF Module and DF-Bluetooth Module
  • Five I2C Interface Pin Sets
  • Two way Motor Drive with 2A maximum current
  • 5 key inputs
  • DC Supply:USB Powered or External 7V~12V DC。
  • DC Output:5V /3.3V DC and External Power Output
  • Dimension:90x80mm

DFRduino RoMeo Pinout

Fig1: Romeo Pin Out

The picture above shows all of the I/O lines and Connectors on the Romeo, which includes:

  • One Regulated Motor Power Input Terminal (6v to12v)
  • One Unregulated Servo Power Input Terminal (you supply regulated 4v to 7.2v)
  • One Servo input power selection jumper
  • One Serial Interface Module Header for APC220/Bluetooth Module
  • Two DC Motor Terminals – Handles motor current draw up to 2A, each terminal
  • One I2C/TWI Port – SDA, SCL, 5V, GND
  • One Analog Port with 8 analog inputs – Analog input 7 will be occupied when connecting "A7" jumper
  • One General Purpose I/O Port with 13 I/O lines – 4,5,6,7 can be used to control motors
  • One Reset Button
  • Jumper bank to Enable/Disable Motor Control

Before you start

Applying Power

This is one of the most important steps in getting the Romeo up and communicating with your host controller. You MUST make sure that you apply power to the Power Terminal using the correct polarity. Reverse Polarity will damage the Romeo. We are not responsible for such damage, nor do we warranty against such damage. Make sure you take time to apply power correctly. Otherwise, it could get costly for you!

Power from USB: Simply plug USB cable, and the Romeo is able to work. Please notice that the USB can only supply 500 mA current. It should be able to meet the most requirements for LED lit application. However it is not enough to power DC motors or servo.

Power from Motor Power Input: Simply connect the ground wire from your supply to the screw terminal labeled “GND”, and then connect the positive wire from your supply to the screw terminal labeled “VIN".

NOTE: Maximum supply voltage cannot exceed 14V DC.

Software

RoMeo can be programmed by Arduino IDE 0022 and above. It can be downloaded at Arduino.cc, Please select “Arduino UNO” as the hardware.

Romeo Configuration

Servo Power Select Jumper

As most servos draw more current than the USB power source can supply. A separate servo power terminal is provided to power the servo individually. This option can be Enabled/Disabled by the Servo Power Select Jumper.

When the Servo Power Select Jumper is applied, the servo is powered by internal 5V.

When the Servo Power Select Jumper is not applied, the servo is powered by external power source.

The Romeo V1.0 uses an automatic switcher for the power source selection. When the external power source has been applied, the servo will be automatically powered by the external power instead of USB power.

Motor Control Pin Jumper

Applying the Motor Control Pin Jumpers will allocate Pin 5,6,7,8 for motor control.

Removing the jumpers will release the above Pins, and the motor controller will be disabled.


افزودن به لیست مقایسه نظرات بازگشت
کپی‌رایت © 2024 ایران ماژول الکترونیک
راه اندازی شده توسط فروشگاه ساز ویرچو