انتخاب واحد پولی:
فارسی انگلیسی
سبد خرید: (0) مورد
خوش آمدید, کاربر گرامی
پشتیبانی آنلاین
Live Support
شاخه ها
اطلاعيه ها
اطلاعيه هامرا از تغييرات محصول ماژول گیرنده GPS/GLNS مدل NEO-7M با آنتن سرامیکی آگاه كن.
سبد خريد
 
0 مورد
مقایسه محصولات
محصولی برای مقایسه انتخاب نشده است!
ورود به سيستم
آدرس پست الكترونيك:
كلمه عبور:

کلمه عبورتان را فراموش کرده اید؟
هنوز ثبت نام نکرده اید؟
تگ محصولات
مقالات
مقالات جدید
تمامی مقالات
تمامی موضوعات
 مقالات متفرقه
RSS مقالات

ماژول گیرنده GPS/GLNS مدل NEO-7M با آنتن سرامیکی[GPS-00027]کد کالا : GPS-00027

ماژول گیرنده GPS/GLNS مدل NEO-7M با آنتن سرامیکی
قیمت: ناموجود
 
 
ماژول گیرنده GPS/GLNS مدل NEO-7M با آنتن سرامیکی

The U-blox NEO-7M GPS Module is ideal for all sorts of development boards, Arduino projects and more. It can operate on voltages between 3 and 6V DC, and has a simple serial output which blasts out the NMEA GPS data at 9600 baud.

Arduino users - this works perfectly with the TinyGPS++ library. With the 7M you can also extract navigation data with this Arduino library.

Specfications:

Pinouts:

  • GND - GND
  • Vcc - connect to 5V or 3.3V
  • TX - data from GPS module - connect to your board's RX pin
  • RX - data to the GPS module - connect to your board's TX pin
  • PPS - time pulse output

More information:

Introduction

GPS module that uses GPS and GLONASS satellites.

Specifications:
  • GPS
  • GLONASS

Wiring

A GPS receiver is rather ‘chatty’, so it is strongly advised to use hardware serial ports.

The ESP8266 only has 2 HW serial ports, but only Serial0 uses a HW RX pin. The TX channel from the ESP to the GPS is not needed for this plugin.

The used baudrate is 9600 bps.

ESP                         Neo-7M (HW Serial0)
GPIO (3/RX/RX0/D9)   <-->   TXD
GPIO (1/TX/TX0/D10)  <-->   RXD
ESP                         Neo-7M (HW Serial0 swapped)
GPIO (13/D7)         <-->   TXD
GPIO (15/D8)         <-->   RXD
ESP                         Neo-7M (HW Serial1)
not used             <-->   TXD
GPIO (2/D4)          <-->   RXD
Power
5.0V                 <-->   VCC
GND                  <-->   GND

Danger

If you use HW Serial0 or HW Serial0 swapped you must disable serial port in the advanced settings! If you fail to do so the unit will not work properly.

Setup

../_images/P082_Setup_Neo-7M_1.png

A screenshot of a later relase of the plugin. The use of hardware serial communication makes the transfer between the GPS and ESP a LOT more stable:

../_images/P082_Setup_1.png

Task settings

  • Device: Name of plugin
  • Name: Name of the task (example name GeoPos)
  • Enable: Should the task be enabled or not

Sensor

  • GPIO <– TX: Used to communicate with the GPS unit.
  • GPIO –> RX: Not used (optional), to push commands back into the GPS unit.
  • GPIO –> PPS: Experimental (optional), used to let the GPS unit update the time of the ESP.
  • DropdownSoftwareSerial lets you select any GPIO pin, HW Serial0 is the preferred (most stable),
    HW Serial0 swapped is similar to Serial0, HW Serial1 is only able to receive data from the GPS unit.

Warning

It’s highly recommended you use either the HW Serial1 or HW Serial0 for stable reading of the GPS unit. But also remember to disable the serial in the advanced settings page, if not the ESP will interfere with the GPS unit.

PPS pin

Some GPS receivers have a PPS pin. This can be used to get a very accurate time reference. According to Wikipedia this signal could be considered a “stratum-1 time source”.

The signal on the PPS pin is a high pulse of +/- 100 msec and the rising edge signals the start of a second. The time reported after this pulse describes the past rising edge of the PPS pulse.

Note

Currently the PPS feature is not thoroughly tested yet, so consider it experimental.

Data acquisition

  • Send to controller 1..3: Check which controller (if any) you want to publish to. All or no controller can be used.
  • Interval: How often should the task publish its value (5..15 seconds is normal).

Indicators (recommended settings)

IndicatorValue NameIntervalDecimalsExtra information
LongitudeLong165 decimals = 100cm resolution, 6 decimals = 10cm resolution, 7 decimals = 1cm resolution
LatitudeLat165 decimals = 100cm resolution, 6 decimals = 10cm resolution, 7 decimals = 1cm resolution
AltitudeAlt10Normally only full meters are needed. Use more decimals if you need higher resolution.
Speedmps11Meters per second.

Note

These resolutions are given at the equator. Less accuracy is received the further north/south you go.

Rules examples

on GeoPos#Speed do
 if [GeoPos#Speed]>50
   //Whooohooo, fast as lightning!
 endif
endon

Events

EventExample
GPS#GotFix Will trigger when the GPS unit got a good position from the satellites.
on GPS#GotFix do
 GPIO,2,1 //LED on
endon
GPS#LostFix Will trigger when the GPS unit is not having a good position from the satellites.
on GPS#LostFix do
  GPIO,2,0 //LED off
endon

افزودن به لیست مقایسه نظرات بازگشت
کپی‌رایت © 2024 ایران ماژول الکترونیک
راه اندازی شده توسط فروشگاه ساز ویرچو